Přizpůsobitelná nášivka ID panelu: průvodce velikostmi a nastavením

By K9 Tactical Gear Inc | Published: 2026-10-31

Category: Návody

Zjistěte, jak zvolit velikost a připevnit přizpůsobitelnou identifikační destičku na obojek nebo postroj vašeho psa. Správně slučte destičky 1.5" nebo 1.75" a vyhněte se běžným chybám při nastavení.

Quick answer

Measure your collar or harness webbing first, then order the ID panel width that matches it: 1.5" for 1.5" gear and 1.75" for 1.75" gear. Attach the panel so the text sits flat and centered, and check that it stays put during walks.

Why width matching matters more than font choice

An ID panel that is too wide will overhang the webbing and catch on brush or leash hardware; one that is too narrow leaves exposed hook-and-loop and looks unfinished. The two panels here are sold in fixed widths, so the collar or harness you already own determines which one you need. Font and material options only matter after you have confirmed the width.

When to choose 1.5" and when to choose 1.75"

The 1.5" panel fits collars and harnesses built on 1.5" webbing, including the Tac 2 1.5", Air Light Collar 1.5", Everyday Collar 1.5", and Tac Collar with Handle 1.5". The 1.75" panel fits a wider set of gear, from the Original Tac Collar 1.75" and Everyday Collar 1.75" to the Defender Harness Neck, Defender Harness Mesh, and Garmin Collar 1.75". If your gear is not on either list, measure the webbing before ordering rather than guessing.

A note on personalization limits

The catalog lists five font options and fifteen solid and pattern materials for the 1.5" panel, but it does not specify character limits or exact placement. Keep your text short and check the current product page for any field limits before you finalize an order. If you need a very long line of text, a wider panel gives you more room but still may not fit everything.

Step-by-step setup

Measure the webbing: Use a ruler or tape measure to check the width of the collar or harness strap where the panel will sit. Measure across the flat webbing, not around the dog. Write the measurement down and compare it to the panel width before ordering.
Match the panel to your gear: Choose the 1.5" panel only if your collar or harness is on the 1.5" compatibility list; choose the 1.75" panel only if your gear is on the 1.75" list. If your model is not listed, do not assume it will fit. A panel that is not listed for your model may overhang or leave gaps.
Position the panel before pressing: Place the panel on the strap so the text is centered and readable from the front, and so the edges do not extend past the webbing. Lightly mark the spot if needed. Check placement with the collar on the dog, since curved straps can shift the panel.
Attach and press firmly: Press the panel down along its full length, working from the center outward. Make sure the hook-and-loop surfaces engage completely. A partially attached panel can peel up during walks.
Test the hold: Put the collar or harness on your dog and tug gently at the panel edges. If it lifts, reposition and press again. Recheck the panel after the first few outings, especially in wet or muddy conditions.

Product facts

Customizable ID Panel 1.5": The 1.5" panel is compatible with the Tac 2 1.5", Air Light Collar 1.5", Everyday Collar 1.5", Tac Collar with Handle 1.5", and Defender Mesh Backing. Check your collar model against this list before ordering to avoid a panel that does not match your webbing.
Customizable ID Panel 1.5"
Customizable ID Panel 1.75": The 1.75" panel is compatible with a long list of 1.75" collars, harnesses, training bags, and the Garmin Collar 1.75". If you already own 1.75" gear, this panel is the likely fit, but confirm your exact model is listed.
Customizable ID Panel 1.75"